SC-11 Mitsubishi FX/1N/1S/2N/3U Series PLC programming cable
lahiru Dhananjaya

FX3U ENET ADP Mitsubishi Electric Ethernet Interface Block

Specification

• • Manufacturer: Mitsubishi Electric
  • Product No.: FX3U-ENET-ADP
  • Product type: Ethernet Interface Block
  • Transmission Specifications Data transmission speed: 100Mbps or 10Mbps,
  • Communication mode: Full / half duplex
  • Transmission method: Baseband
  • The maximum segment length: 100m
  • The maximum number of nodes / connection: 10BASE-T: cascade up to four stages
    100BASE-TX: cascade up to two-stage
  • above is the connection possible number of stages at the time of use repeater hub.
    Can be connected to the number of stages at the time of switching hub used, please check with the manufacturer of the switching hub to be used.
  • Connector: RJ45
  • Number of connections: MELSOFT connection + MC protocol + data monitoring ? 4 connection
  • It can be connected to the number of the basic unit: One
    Ethernet adapter, as well as the communication function expansion board and other communication special adapter, and 1 channel the communication channel (CH) occupation.
  • Apply PLC: FX3S, FX3G (V2.00 or later), FX3U (since V3.10), FX3GC (V2.00 or later), FX3UC (V3.10 or later)
    connection to the FX3S is required FX3S-CNV-ADP.
    Connection to the FX3G is required FX3G-CNV-ADP.
    FX3U, connection to the FX3UC-32MT-LT (-2), you must have the function expansion board.

Power Specifications:

• Power supply: 30mA / DC5V (internal power supply from DC5V power of the basic unit)
• Allowable momentary power failure time: As well as the sequencer to connect
• Ambient temperature: 0 ~ 55 °C ····· operation, -25 ~ 75 °C ····· during storage
• Relative humidity: 5 ~ 95% RH (non-condensing) …… operation
• Vibration resistance When the DIN rail mounting Frequency: 10 ~ 57Hz: Half amplitude: 0.035mm X, Y, Z each direction 10 times (for a total of each 80 minutes)
• Frequency: 57 ~ 150Hz: Acceleration: 4.9m / s2 X, Y, Z each direction 10 times (for a total of each 80 minutes)
• Direct mounting at the time Frequency: 10 ~ 57Hz: Half amplitude: 0.075mm X, Y, Z each direction 10 times (for a total of each 80 minutes)
• Frequency: 57 ~ 150Hz: Acceleration: 9.8m / s2 X, Y, Z each direction 10 times (for a total of each 80 minutes)
• Impact resistance: 147m / s2, duration of action 11ms, X at half-sine pulse, Y, Z directions 3 times each
• Anti-noise: Noise voltage 1,000Vp-p, noise width 1µs, due to rising 1ns, cycle 30 ~ 100Hz of noise simulator
• Withstand voltage: All terminals and between the ground terminal: AC500V 1 minute
• Insulation resistance: All terminals and between the ground terminal: DC500V 5MO more in insulation resistance tester
• Working environment: Corrosive, there is no flammable gas, conductive dust (dust) that is not terribly
• Use advanced: 2000m or less cannot use in the pressurized environment to more than atmospheric pressure. There is a possibility of failure.
• Shipping Weight: 1.5 Kg

Packages include:

1x FX3U ENET ADP Mitsubishi Electric

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

FX3U ENET ADP Mitsubishi Electric Ethernet Interface Block
lahiru Dhananjaya

I/O expansion unit FX2N-32ER-ES/UL

• Manufacturer : Mitsubishi Electric
• FX2N-32ER-ES/UL
• I / O expansion unit FX2N – 32ER – ES / UL
• Application sequencer : FX1N, FX3G, FX2N, FX3U
• mass : 0.65 Kg
• Rated voltage : AC 100 V to 240 V
• Voltage tolerance range : AC 85V ~ 264V
• Rated frequency : 50/60 Hz
• Power supply fuse : 250 V 3.15 A (3A)
• Inrush current : AC 100 V: maximum 40 A 5 ms or less AC 200 V: maximum 60 A 5 ms or less
• power consumption : 30 W
• 24 VDC service power supply : 24 VDC 250 mA or less When input / output expansion block is connected, 24 VDC service power is consumed.
• Input specification :
• Number of input points : 16 points
• Input connection shape : Removable terminal block (M3 screw)
• Input format : Sink / source
• Input signal voltage : DC 24 V ± 10%
• Input impedance : 4.3 kΩ
• Input signal current : 5 mA / 24 VDC
• Input ON sensitivity current : 3.5 mA or more
• Input OFF sensitivity current : 1.5 mA or less
• Input response time : About 10 ms
• Input signal format : Sink: no-voltage contact input or NPN open collector transistor source: no-voltage contact input or PNP open collector transistor
• Input circuit insulation : Photocoupler insulation
• Input operation display : LED on the panel when input is ON
• Number of output points : 16 points
• Output connection shape : Removable terminal block (M3 screw)
• Output type / format : relay
• External power supply : DC 30 V or less AC 240 V or less (When not compliant with CE, UL, cUL standard, AC 250 V or less)
• Maximum load Resistive load : Please set the total load current per 2A / 1 point common as follows. . Output 4 points / common: 8 A or less
• Inductive load : 80VA
• Minimum load : DC 5 V 2 mA (reference value)
• Response time OFF → ON : About 10 ms
• ON → OFF : About 10 ms
• Circuit insulation : Mechanical insulation
• Output operation indication : LED lit when relay coil is energized
• Ambient temperature : 0 to 55 ° C. … Operating -25 to 75 ° C. ….. Save
• Relative humidity : 5 to 95% RH (noncondensing)…. in operation
• Anti-vibration When DIN rail is installed Frequency: 10 to 57 Hz : One amplitude: 0.035 mm X, Y, Z 10 times in each direction (80 minutes in total) The criteria are based on IEC 61131-2
• Frequency: 57 to 150 Hz : Acceleration: 4.9 m / s 2 Ten times in each of X, Y, Z directions (80 minutes in total in total) The criterion is based on IEC 61131-2
• Direct installation Frequency: 10 to 57 Hz : One amplitude: 0.075 mm X, Y, Z 10 times in each direction (80 minutes in total) The criteria are based on IEC 61131-2
• Frequency: 57 to 150 Hz : Acceleration: 9.8 m / s 2 X, Y, Z 10 times in each direction (80 minutes in total) The criteria are based on IEC 61131-2
• Impact resistance : 147 m / s 2 , working time 11 ms, criterion for judgment three times in X, Y, Z directions by sine half-wave pulse is according to IEC 61131-2
• Noise immunity : Noise voltage with 1,000 Vp-p, noise width 1 μs, rising 1 ns, with noise si
• tor with period of 30 to 100 Hz
• Withstand voltage : Between the power supply terminal (AC power supply) and the earth terminal: AC 1500 V for 1 minute 24 VDC Service power supply and between the input terminal (24 VDC) and the earth terminal: 500 V AC for 1 minute Between the output terminal (relay)
• Insulation resistance : Between each terminal and earth terminal: 500 MV DC 500 MΩ or more with an insulation resistance meter
• ground : Class D grounding (grounding resistance: 100 Ω or less)Grounding should be dedicated ground or common ground.
• Use atmosphere : There is no corrosive property, flammable gas, conductive dust (dust) is not serious
• Use altitude : Can not be used in an environment pressurized to 2000 m or less under atmospheric pressure. It may break down.
• Shipping Weight : 1.7 Kg

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

I/O expansion unit FX2N-32ER-ES/UL
lahiru Dhananjaya

• Manufacturer : Mitsubishi Electric
• Product No. : FX2N-16EX-ES/UL
• Product type : Input Module Extension Block
• Integrated Inputs : 16 (24 VDC)
• Integrated Inputs / Outputs : 16
• ON Voltage (Max.) : Relay version: < 240 VAC, < 30 VDC; Transistor version: 5 – 30 VDC; Triac version: 85 – 242 VAC
• Stocked Item : S
• 5VDC Current Consumption (mA) : 45
• Dimensions (LxWxH) : 8.7cm x 4cm x 9cm
• Weight : 0.3 Kg
• Shipping Weight : 2 Kg

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

FX2N-16EX-ES/UL Mitsubishi Electric Input Module Extension Block
lahiru Dhananjaya

Mitsubishi FX3U Logic Module – 32 Inputs, 32 Outputs, Relay, Computer, HMI Interface

Mitsubishi Electric Logic Module

The Mitsubishi FX3U series logic module has 32 inputs and 32 relay outputs with a contact rating of 8A. This DIN rail mount logic module has a screw termination method. It has a large memory for applications that require a large space. This logic module has a supply voltage that ranges between 100VAC and 240VAC.
Mitsubishi FX3U
FX3U CPU’s are compatible with existing FX2N expansion modules as well as the new FX3U ADP expansion modules and may be used as a replacement for FX2N PLC’s.

Features and Benefits

Expandable compact PLC
I/O,ADP & special function modules available
Exchangeable interface & I/O adapter boards
Operating temperature ranges between 0°C and 50°C
High processing speed
64K steps battery-backed RAM memory
249 applied instructions, 7680 auxiliary relays, 512 timers, 251 counters and40768 data registers
0.065μs/basic instruction
Backward compatibility
Password access protection

Applications

Industrial sites
Factory automation

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

Mitsubishi FX3U Logic Module – 32 Inputs, 32 Outputs, Relay, Computer, HMI Interface
lahiru Dhananjaya

Mitsubishi PLC Programming USB SC09 FX Cable

This SC09 FX Cable the upgrade version of the black PLC Cablefor MESLEC FX series. Suitable for: Mitsubishi FX2N/FX1N/FX0/FX0N/FX0S/FX1S/FX3U USB/RS422 interface for Mitsubishi FX series only, with communication indicator

Specification :

• Cable length: 3 meters
• PC USB 2.0
• PLC end of round 8-pin
• 3-color LED indicator Communication
• the new cable, yellow appearance.
• English FIDI original conversion microarrays.
• gold-plated plugs, anti-rust.
• the entire board using SMT technology.
• standardized test of artificial testing, quality is guaranteed.
• using zinc alloy casing

Package Included:

1 x USB- PLC Cable

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

Mitsubishi PLC Programming USB SC09 FX Cable
Ashen Premathilake

Mitsubishi PLC Programmable Controller FX3U

 

Mitsubishi PLC Programmable Controller FX3U
Ashen Premathilake