Servo SG90 9g 180 Degree

The SG90 is a popular micro servo motor commonly used in various hobbyist and robotics projects due to its affordability, ease of use, and reliability. Here are the specifications for the SG90 servo motor:

Specifications:

• Dimensions:
  • Length: 23 mm
  • Width: 12.2 mm
  • Height: 29 mm
• Weight: 9 grams
• Operating Voltage: 4.8V to 6.0V
• Stall Torque:
  • At 4.8V: 1.8 kg·cm (25 oz·in)
  • At 6.0V: 2.2 kg·cm (31 oz·in)
• Operating Speed (no load):
  • At 4.8V: 0.12 sec/60°
  • At 6.0V: 0.10 sec/60°
• Rotation Range: 180 degrees (±90 degrees)
• Control System: PWM (Pulse Width Modulation)
• Pulse Width Range: 500-2400 microseconds
• Neutral Position: 1500 microseconds
• Dead Band Width: 10 microseconds
• Connector Wire Length: Approximately 25 cm
• Gear Type: Nylon gears
• Bearing Type: None (bushing)

Typical Pin Configuration:

• Brown/Black Wire: Ground (GND)
• Red Wire: Power (VCC)
• Orange/Yellow Wire: Signal (PWM control)

Selecting your Servo Motor

There are lots of servo motors available in the market and each one has its own specialty and applications. The following two paragraphs will help you identify the right type of servo motor for your project/system.

Next comes the most important parameter, which is the torque at which the motor operates. Again there are many choices here but the commonly available one is the 2.5kg/cm torque which comes with the Towerpro SG90 Motor. This 2.5kg/cm torque means that the motor can pull a weight of 2.5kg when it is suspended at a distance of 1cm. So if you suspend the load at 0.5cm then the motor can pull a load of 5kg similarly if you suspend the load at 2cm then can pull only 1.25. Based on the load which you use in the project you can select the motor with proper torque. The below picture will illustrate the same.

How to use a Servo Motor

After selecting the right Servo motor for the project, comes the question how to use it. As we know there are three wires coming out of this motor. The description of the same is given on top of this page. To make this motor rotate, we have to power the motor with +5V using the Red and Brown wire and send PWM signals to the Orange colour wire. Hence we need something that could generate PWM signals to make this motor work, this something could be anything like a 555 Timer or other Microcontroller platforms like Arduino, PIC, ARM or even a microprocessor like Raspberry Pie. Now, how to control the direction of the motor? To understand that let us a look at the picture given in the datasheet.

From the picture we can understand that the PWM signal produced should have a frequency of 50Hz that is the PWM period should be 20ms. Out of which the On-Time can vary from 1ms to 2ms. So when the on-time is 1ms the motor will be in 0° and when 1.5ms the motor will be 90°, similarly when it is 2ms it will be 180°. So, by varying the on-time from 1ms to 2ms the motor can be controlled from 0° to 180°

Applications

• Used as actuators in many robots like Biped Robot, Hexapod, robotic arm etc..
• Commonly used for steering system in RC toys
• Robots where position control is required without feedback
• Less weight hence used in multi DOF robots like humanoid robots

SG90 Servo Motor Dimensions

Data Sheet of 9G Servo motor –https://components101.com/sites/default/files/component_datasheet/SG90%20Servo%20Motor%20Datasheet.pdf

Servo SG90 9g 180 Degree
lahiru Dhananjaya