PCA9685 Servo motor Driver 16 Channel 12-bit PWM

lahiru Dhananjaya — Wed, 26 Oct 2022 00:43:16 +0000

LK Tronics
PCA9685 Servo motor Driver 16 Channel 12-bit PWM

PCA9685 Servo motor Driver 16 Channel 12-bit PWM

The PCA9685 Servo Motor Driver is a high-performance device that enables precise control of up to 16 servo motors. With its advanced features and easy-to-use interface, this driver is ideal for a wide range of applications, from robotics and automation to hobby projects and DIY electronics. Get yours today and experience the power and precision of the PCA9685 Servo Motor Driver.

Features:

Dimensions (no headers or terminal block) 2.5″ x 1″ x 0.1″ (62.5mm x 25.4mm x 3mm)
Weight (no headers or terminal block): 5.5grams
Weight (with 3×4 headers & terminal block): 9grams
This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers
Terminal block for power input (or you can use the 0.1″ breakouts on the side)
Reverse polarity protection on the terminal block input
Green power-good LED
3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1″ so you can only stack 4 next to each other on 0.1″ header
“Chain-able” design
A spot to place a big capacitor on the V+ line (in case you need it)
220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
Solder jumpers for the 6 address select pins
i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs – that’s a lot of servos or LEDs
Adjustable frequency PWM up to about 1.6 KHz
12-bit resolution for each output – for servos, that means about 4us resolution at 60Hz update rate
Configurable push-pull or open-drain output
Output enable pin to quickly disable all the outputs

(1) Drive board connected to Arduino:

The PWM driver board uses the I2C method, so only four lines can be connected to the Arduino device:

“Classic” Arduino pin mode:

+ 5v -> VCC

GND -> GND

Analog 4 -> SDA

Analog 5 -> SCL

Old Mega pin way:

+ 5v -> VCC

GND -> GND

Digital 20 -> SDA

Digital 21 -> SCL

R3 and later Arduino pin method (Uno, Mega &

Leonardo):

(These boards have dedicated SDA and SCL pins)

+ 5v -> VCC

GND -> GND

SDA -> SDA

SCL -> SCL

VCC pin is only for the chip power supply, if you want to connect the servo or LED lights, use the V + pin power supply, V + pin supports 3.3 ~ 6V power supply (chip safe voltage 5V). It is recommended to connect the external power supply via the power supply terminal.

(2) power supply part:

Most of the servo design voltage is 5 ~ 6V, especially in a number of steering gear at the same time running, with the need for high-power power supply. If you are directly using the Arduino 5V pin to power the servo directly, there are some unpredictable problems, so we recommend that you have a suitable external power supply for the drive board.

(3) Connect the servo:

Most servos are connected using standard 3-wire female plugs, as long as the corresponding pin into the driver board on it. (Ground wire is generally black or brown, the signal line is generally yellow or white)

(4) for the driver board assigned address:

Each drive board of the cascade needs to have a unique access address. The initial I2C address of each driver board is 0 × 40, you can modify the upper right corner of the jumper I2C address. Connect a jumper with solder to indicate a binary number “1”.

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

PCA9685 Servo motor Driver 16 Channel 12-bit PWM
lahiru Dhananjaya

Servo motor Driver | LK Tronics

PCA9685 Servo motor Driver 16 Channel 12-bit PWM