12v 5A Power Switching Adapter Supply with Cable

12v 5A Power Switching Adapter Supply with Cable

Specifications:

• Input Voltage: 100-240V AC, 50/60Hz
• Output Voltage: 12V DC
• Output Current: 5A (maximum)
• Output Power: 60W (maximum)
• Efficiency: Typically ≥ 80%
• Ripple & Noise: ≤ 120mVp-p
• Load Regulation: ± 5%
• Line Regulation: ± 1%

Protection Features:

• Over-Voltage Protection (OVP)
• Over-Current Protection (OCP)
• Short-Circuit Protection (SCP)
• Over-Temperature Protection (OTP)

Physical Specifications:

• Connector Type: DC barrel connector (commonly 5.5mm outer diameter, 2.1mm)
• Cable Length: Typically 1.2m (can vary depending on the manufacturer)
• Adapter Dimensions: Approx. 110mm x 45mm x 30mm

Environmental Specifications:

• Operating Temperature: 0°C to 40°C
• Storage Temperature: -20°C to 85°C
• Humidity: 5% to 95% non-condensing

Compliance & Certifications:

• Certifications: CE, FCC, RoHS, UL (depending on the manufacturer)
• Safety Standards: Meets or exceeds safety standards for power supplies

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

12v 5A Power Switching Adapter Supply with Cable
darazsales

12V Power Adapter DC 4000mA MYX-1204000E

INTRODUCTION

• •  12V Power Adapter Very low standby power achieved
• • Reliability level or 10000 hours MTBF& 0.5% annual field failure rate@25℃

INPUT REQUIREMENTS

• • • AC Input voltage rating 100Vac to 240Vac
  • • AC Input voltage range 90Vac to 264Vac
  • • AC Input frequency range 47Hz to 63Hz
  • • Max. In-rush current 30A for 100Vac at full load<75A for 240Vac at full load
  • • Input current 1.5A Max @ 90V/60Hz full load
  • • Standby power 0.3W Max @ 230V/50Hz no load

OUTPUT REQUIREMENTS

• • • Output voltage +12V
  • • Output voltage tolerance +/-0.5V%
  • • Min load current 0 mA
  • • Max load current 5000 mA
  • • Line regulation +/-1%
  • • load regulation +/-0.5
  • • Ripple & Noise 300mVp-p (max)

DC-20MHz/Ripple and Noise is measured on output connector with 20MHz oscilloscope
bandwidth differentially with a 10uF electrolytic and 0.1uF ceramic capacitors across output

• • Total output power 60W typical
• • Efficiency 86% min@115~230Vac50/60Hz with full load
• • Hold up time 10 sec.min.@ 100Vac/60Hz with full load
• • Turn on delay time 3sec.max.@ 100Vac/60Hz with full load
• • Switching frequency 65K Hz typical

PROTECTION FUATURES

• • Over-voltage protection Output shut down (Auto recovery) When output voltage exceeds
• • Over-current protection Output shut down (Auto recovery) When output current exceeds
• • Short circuit protection Output shut down (Auto restart)

ENVIRONMENTAL

• • Operation temperature -20℃ to +40℃
• • Operation humidity 20% to 90% R.H.
• • Storage temperature -20℃ to +75℃
• • Storage humidity 0% to 90% R.H.

SAFETY REQUIREMENTS AND CERTIFICATION

Regulatory Standard
The power supply shall comply the following international regulatory standards
Dielectric withstand (Hi-pot) test
• Input to output 3000Vac 10mA /60S
Insulation
• Input to output DC 500V 10M ohm Min

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

Power Adapter DC12V 4000mA MYX-1204000E
lahiru Dhananjaya