ARDUINO UNO ATmega 328P

The 14 digital input/output pins in Arduino Uno ATmega 328P can used as input or output pins by using pinMode(), digitalRead(), and digital Write () functions in Arduino programming.

Each pin operates at 5V can provide or receive a maximum of 40mA current and has an internal pull-up resistor of 20-50 KOhms which are disconnect by default. Buy Arduino Uno ATmega 328P

How to use Arduino Board

Out of these 14 pins, some pins have specific functions as listed below, you can find the Pin Description in Arduino Uno

• Serial Pins 0 (Rx) and 1 (Tx): Rx and Tx pins are using to receive and transmit TTL serial data. They are connected with the corresponding ATmega328P USB to the TTL serial chip.
• External Interrupt Pins 2 and 3: These pins can configure to trigger an interrupt on a low value, a rising or falling edge, or a change in value.
• PWM Pins 3, 5, 6, 9, and 11: These pins provide an 8-bit PWM output by using the analog Write() function.
• SPI Pins 10 (SS), 11 (MOSI), 12 (MISO) and 13 (SCK): These pins are used for SPI communication.
• In-built LED Pin 13: This pin is connected with a built-in LED, and pin 13 is HIGH–the LED is on and pin 13 is LOW, it’s off.
• Analog pin 4 (SDA) and pin 5 (SCA) are used for TWI communication using the Wire library.

Arduino Uno has a couple of other pins as explained below:

• AREF: Used to provide a reference voltage for analog inputs with analogReference() function.
• Reset Pin: Making this pin LOW, resets the microcontroller.

Pin Description in Arduino Uno ATmega 328P

Refer to the below table for the Pin Description in Arduino Uno. Any problems? direct message us

Arduino Uno Technical Specifications

Arduino Communication 

A computer, an additional Arduino board, and other microcontrollers can all connect with Arduino. The ATmega328P microcontroller provides UART TTL (5V) serial communication which can do using digital pin 0 (Rx) and digital pin 1 (Tx). An ATmega16U2 on the board channels this serial communication over USB and appears as a virtual COM port to software on the computer. The ATmega16U2 firmware uses the standard USB COM drivers, and no external driver is need. on Windows, a .inf file is require.

The Arduino software

The Arduino software includes a serial monitor that allows simple textual data to send to and from the Arduino board. There are two RX and TX LEDs on the Arduino board which will flash, after data is being transmit via the USB-to-serial chip and USB connection to the computer (not for serial communication on pins 0 and 1). A Software Serial library allows for serial communication on any of Uno’s digital pins. The ATmega328P supports I2C (TWI) and SPI communication. The Arduino software includes a Wire library to simplify the use of the I2C bus. Buy Arduino uno Sri Lanka to make your work easy.

ARDUINO UNO ATmega 328P Pin Mapping

The pin mapping between the Arduino Uno and ATmega328 chip

Software

Arduino IDE (Integrated Development Environment) is requiring programming the Arduino Uno board. Download it here.

Programming Arduino

Arduino IDE is install on the computer, connect the board to the computer using a USB cable. Now open the Arduino IDE and choose the correct board by selecting>Tools>Boards>Arduino/Genuine Uno. choose the correct Port by selecting Tools>Port. Arduino Uno is the program using Arduino programming language based on Wiring. To get it start with the Arduino Uno board and blink the built-in LED, load the example code by selecting Files>Examples>Basics>Blink. in this example code is load into your IDE, click on the ‘upload’ button given on the top bar. After the upload is finish, you should see the Arduino’s built-in LED blinking.  Below is the example code for blinking:

//The setup function runs once when you press reset or power the board
void setup() {
  // initialize digital pin LED_BUILTIN as an output.
  pinMode(LED_BUILTIN, OUTPUT);
}

//The, loop function runs over and over again forever
void loop() {
  digitalWrite(LED_BUILTIN, HIGH);   // turn the LED on (HIGH is the voltage level)
  delay(1000);                       // wait for a second
  digitalWrite(LED_BUILTIN, LOW);    // turn the LED off by making the voltage LOW
  delay(1000);                       // wait for a second
}

Applications

• Prototyping of Electronics Products and Systems
• Multiple DIY Projects.
• Easy to use for beginner-level DIYers and makers.
• Projects requiring Multiple I/O interfaces and communications.

Download the Data Sheet – Click Here

Arduino Uno Compatible Board

Arduino Nano Controller ATmega328P

Special Notice :

• INCLUDE USB CABLE

Arduino Uno ATmega 328P
pearstec.website

Arduino Uno Compatible Board SMD Version ATmega328P

The Arduino Uno Compatible Board SMD Version ATmega328P is a versatile and user-friendly microcontroller board that is fully compatible with the Arduino Uno. It offers a wide range of features and functionalities, making it ideal for both beginners and experienced users. With its compact size and easy-to-use interface, this board allows for seamless integration with various electronic components and sensors. It also supports a wide range of programming languages, making it suitable for a diverse range of projects. Whether you are a hobbyist or a professional, this is a reliable and efficient choice for all your microcontroller needs.

Same as Arduino Uno specifications only difference is it consists of Arduino Uno SMD version type IC, which cannot replace easily.

• Microcontroller: ATmega328P
• Operating Voltage: 5V
• Input Voltage (recommended): 7-12V
• Input Voltage (limit): 6-20V
• Digital I/O Pins: 14 (of which 6 provide PWM output)
• PWM Digital I/O Pins: 6
• Analog Input Pins: 6
• DC Current per I/O Pin: 20 mA
• DC Current for 3.3V Pin: 50 mA
• Flash Memory: 32 KB (ATmega328P) of which 0.5 KB is used by the bootloader
• SRAM: 2 KB (ATmega328P)
• EEPROM: 1 KB (ATmega328P)
• Clock Speed: 16 MHz
• LED_BUILTIN: 13
• Length: 68.6 mm
• Width: 53.4 mm
• Weight: 25 g

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

If You are interested in Arduino UNO Original Bord – ARDUINO UNO ATmega 328P | LK-Tronics | Free Cable

Arduino Uno Compatible Board
Ashen Premathilake