YF-B10 Hall Effect Flow Sensor Water 1-50L/min Turbine Flowmeter

Explore our website to find the YF-B10 Hall Effect Flow Sensor Water 1-50L/min. Accurately measure water flow rates and ensure efficient monitoring with this high-quality sensor.

Feature:

*Stable, high temperature, low water pressure start.
*Small size, easy to install. Hall element is imported, water-proof design to prevent water ingress, The inside of the impeller is inlaid with a stainless steel shaft and is always wear-resistant.
*Three wire connections: Red for positive, black for negative, yellow for pulse signal.
*The water stream sensor is applied to the water heater and can be used as a stream switch.
*Maximum water pressure: 1.75MPa, stream range: 2-50L/min.

Specification

Model: YF-B10
Interface size: G1
Rated voltage: DC3.5~24V
Inner/Outer Diameter: 24.38mm/32.9mm
Thread length: 13mm
Material: Brass

Water pressure resistance: >1.75MPa
Output pulse high level: >DC4.7V (input voltage DC5V)
Output pulse duty cycle: 50%±10%
Insulation resistance: >100MΩ
Stream range: 2~50L\MIN±5%
Airtightness: close each hole, add 1.7Mpa water pressure test for 1 minute without leakage and deformation
Stream pulse characteristics: F=(8*Q-4)±5%, F is the frequency Q is L/Min, that is, 476 pulses per liter of water

Wiring:
Red IN is connected to the positive pole
Yellow OUT signal output line
Black GND to negative

Packing list:
1*stream sensor

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

YF-B10 Hall Effect Flow Sensor Water 1-50L/min Turbine Flowmeter
darazsales

7 IN 1 Soil Integrated Sensor [EC PH NPK Moisture Temperature Meter]

Overview

7 IN 1 Soil Integrated Sensor EC PH NPK Moisture Temperature Meter

Our soil sensors are used for soil NPK, PH , EC, temperature, and humidity measurement with high accuracy, fast response speed, and stable output. Long-term buried in the soil, resistant to long-term electrolysis, corrosion resistance, vacuum potting, completely waterproof.

Features

• High-precision agriculture sensors, rapid response, good exchangeability
• Good tightness, and corrosion resistance, the soil tester can use in the soil for a long time.
• Flame retardant epoxy resin curing is completely waterproof, and the soil tester can withstand strong external impact.
• Steel needles are made of high-quality materials that can withstand long-term electrolysis, acid, and alkali corrosion in soil.

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

7 IN 1 Soil Integrated Sensor [EC PH NPK Moisture Temperature Meter]
darazsales

DHT22 Digital Temperature and Humidity Sensor

• Operating Voltage – 3 ~ 5.5V
• Accuracy resolution – 0.1
• Humidity range – 0-100%RH
• Temperature range – [-40~80°C]
• Humidity measurement precision – ±2%RH
• Temperature measurement precision – ±0.5°C
• Length (mm): – 43
• Width (mm): – 15
• Height (mm): – 10
• Weight (g): – 7

Features :

1. High precision
2. Capacitive type
3. Full-range temperature compensated
4. Relative humidity and temperature measurement
5. Calibrated digital signal
6. Outstanding long-term stability
7. Extra components not needed
8. Long transmission distance
9. Low power consumption
10. 4 pins packaged and fully interchangeable

Package Includes :

1 x DHT22 Digital Temperature and Humidity Sensor Module AM2302

1 x Connecting Cable

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

DHT22 Digital Temperature and Humidity Sensor
darazsales

LJ18A3-8-Z-BX Proximity Sensor 8mm Inductive NPN NO Switch DC 6-36V

Explore LJ18A3-8-Z-BX Proximity Sensor8mm Inductive, the ultimate source for top-notch inductive sensors. Enhance your industrial processes with reliable and efficient automation technology.

• Product Name: Inductive Proximity Switch
• Model : LJ18A3-8-Z/BX
• Wire Type: DC 3 Wire Type (Black, Brown, Blue)
• Switch Appearance Type: Cylinder Type
• Theory: Inductive Sensor
• Output Type: PNP NO(Normal Open)
• Diameter of Head: 18mm
• Detecting Distance: 8mm
• Supply Voltage: DC 6-36V
• Current Output: 300mA
• Detect Object: Iron
• External Material: Plastic, Alloy
• Net Weight: 80g
• It is a component widely used in the automatic control industry for detecting, controlling, and noncontact switching.
  When the proximity switch is close to some target object, it will send out a control signal.
  It’s widely used in machines, paper making, the light industry for limiting stations, orientation taking counts, speeding trials etc.
  Package Content: 1 x Inductive Proximity Switch

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

LJ18A3-8-Z-BX Proximity Sensor 8mm Inductive NPN NO Switch DC 6-36V 
darazsales

RS PRO PT100 RTD Sensor, 6mm Dia, 150mm Long, 3 Wire, G1/2, Class B +450°C Max

The PRO PT100 RTD Sensor is a high-quality temperature sensor designed for accurate and reliable measurements. It features a platinum resistance element that ensures precise temperature readings with a wide operating range. The sensor is built with durable materials and is suitable for various industrial applications. With its compact design and easy installation, RTD Sensor is an excellent choice for monitoring temperature in demanding environments.

Z Card 2 page (rs-online.com)

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

RS PRO PT100 RTD Sensor, 6mm Dia, 150mm Long
lahiru Dhananjaya

Xkc Water Level Sensor Switch XKC-Y25-V
lahiru Dhananjaya

Industrial Pressure Sensor (0bar – 500mbar)

RS PRO Industrial Pressure Sensors – IPSL Series

These IPSL-series Pressure Sensors, also known as pressure transmitters from our own RS PRO brand are suitable for wide range of industrial applications. These devices change pressure forces into electrical signals. They are used to measure the pressure of the specific quantity like air, water and gas by changing the pressure into electrical energy. The probe uses a piezo-resistive ceramic sensor, giving excellent media compatibility within a stainless-steel housing.

Features and Benefits

Material Specifications

Applications

Characteristics

The electronics incorporate a microprocessor-based amplifier, requiring no adjustments and giving stable electronics, especially for industrial applications. The device is temperature compensated, calibrated and supplied with a traceable serial number and calibration data.

RS PRO

RS PRO is our own brand range and brings you a wide range of high-quality, great value products offering you more choice. Trusted by engineers all over the world, every part of every RS PRO product has been rigorously tested against demanding industry standards; they’re only given the RS PRO Seal of Approval if we’re confident of their exceptional quality, which means you can be confident too.

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

Industrial Pressure Sensor (0bar – 500mbar)
lahiru Dhananjaya

Ambient Light Sensor TEMT6000

Description:

Ambient Sensor TEMT6000 Environmental optical sensor module simulation light intensity module visible module
The TEMT6000 sensor has a maximum sensitivity of 570nm and a wide semi-sensitivity Angle of 60°. Although the device is very sensitive to ambient light, it can suppress infrared (IR) spectra, thus providing higher visible spectral responsiveness similar to the “human eye”.

Specification:

• Operating voltage: DC3.3-5.5V
• Operating temperature:-40–85°C
• llluminance range: 1–1000 lux
• Output signal: Analog voltage, in the 5
• Operating voltage case range 0-5V

Features:

Only sensitive to visible light, no additional filter is required for good linear output

• Pin definition
• VCC – Positive Power
• GND – Power Negative
• OUT – Analog Output

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

Ambient Light Sensor TEMT6000
darazsales

Soil Moisture Sensor with 1.3M Corrosion Resistance Probe

Description:

Soil Moisture Sensor Soil Detector Module Soil Moisture Test Soil Humidity Test with 1.3M Corrosion Resistance Probe for Arduino

Specification:

Voltage: 3.3-12VDC
Current: Work<20ma
Output:<30ma
Interface: +-DOAO DO digital/AO analog
Uses: Detecting soil moisture

Principle: The soil humidity probe detects the humidity, and the voltage comparator judges the humidity.

Operation:

1. Connect the positive pole of the power supply and the negative pole of the power supply.

2. Clockwise/counterclockwise adjustment of the blue potentiometer can improve/decrease the detection sensitivity of the probe.

3. The potentiometer is clockwise adjusted to the output indicator of [S], it indicates that the range of regulation has exceeded the test threshold, and when the counter-clockwise adjustment is unable to adjust, it exceeds the threshold. When adjusting, they should not exceed the threshold value, otherwise, they can not be used normally.

4. A single-chip computer can directly detect the analog (voltage) output of an Analog Output (AO) through its port.

Note:

Please manually measure to allow for differences of 1-3cm.

Package Includes: 1x Sensor | 1x Probe | 1x Pin

What is Soil Moisture Sensor with Arduino

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

Soil Moisture Sensor with Probe 1.3M Corrosion Resistance Probe
darazsales

Carbon Dioxide Sensor MG811 C02 Module Air 

Product Description

MG-811 Carbon Dioxide Sensor Module (MG811 C02 Module) is a (CO2) sensor that is a Metal Oxide, which must heat the tank to the specified level. (With the method of supplying power) will cause heat vapor and separate CO2 from the air. This sensor module has an MG-811 onboard as the sensor component. A signal output circuit for heating the sensor the MG811 C02 Module is highly sensitive to CO2 and less sensitive to alcohol and CO. The output voltage of the CO2 increases.

Product Specification

Operating Voltage 6V
Weight 10g
Height 29
Width 22
Length 32
Detection Zone 0 10000 ppm

Features:

Wide detecting scope.
High sensitivity & stability.
Simple drive circuit.
Digital output: Active low (When it outputs a low-level signal, the indicator LED will be on)Analog output: Two Range Options: 0 to 2V or 0V to 4V. The default is 0V to 2V DC
Compatible with Arduino & Raspberry Pi (for use on analog output with Raspberry Pi you will need an analog to analog-to-digital converter Chip).

VISIT OUR FACEBOOK PAGE FOR MORE INFO | MORE PRODUCT IN OUR SHOP

Carbon Dioxide Sensor MG811 C02 Module Air
darazsales